Nov 02, 2025 Leave a message

Xi'an Jiaotong University's *Acta Materialia* describes a yield strength of 1550 MPa and an elongation of 8.7% in a layered dual-phase titanium alloy! This study investigates the sequential activation of a multi-deformation mechanism in this alloy.

Titanium (Ti) and its alloys have received widespread attention in practical applications due to their excellent properties such as high specific strength and corrosion resistance. In order to improve the mechanical properties of metastable β - titanium alloys, α precipitation strengthening is the most effective method. By adjusting the size, morphology, and distribution of HCP α precipitates in the BCC β matrix, dislocation movement is hindered through the α/β interface. However, the differences in crystal structure, deformation mechanism, and strength between the α and β phases lead to high stress concentration at the α/β interface, which is the reason for the gradual strain localization or severe decrease in microcracks and ductility of biphasic titanium alloys.

 

To address the aforementioned issues, three new strategies have recently been proposed. Firstly, activate various plastic mechanisms of the β phase during the plastic deformation process. For example, the activation sequence of the deformation mechanism of the β matrix from dislocation slip to phase transition is regulated by the precipitation of three functional groups α, thereby enhancing the ductility of the alloy. Secondly, constructing unique heterostructures to alleviate interfacial strain incompatibility, thereby achieving the strain distribution/gradient required for uniform plastic deformation. We have also developed layered structures with multi-scale alpha precipitates in biphasic titanium alloys to reduce stress concentration at the alpha/beta interface and improve ductility Thirdly, utilizing the interstitial O/N elements to refine and strengthen the alpha precipitate, thereby reducing the strength difference between the alpha and beta phases. However, the above three strategies rarely regulate the inherent deformation mechanism of low crystal symmetry alpha precipitates, and the independent slip systems of these precipitates are quite limited. Compared with the reported high-strength duplex titanium alloys (yield strength>1100 MPa), these new titanium alloys have a yield strength exceeding 1500 MPa. However, due to insufficient work hardening ability and lower uniform elongation (<3%), these high-strength duplex titanium alloys still provide a balance between strength and ductility. The key to overcoming this dilemma lies in activating multiple plastic mechanisms of the alpha phase to alleviate strain incompatibility between the alpha and beta phases, improve work hardening rate (WHR), and achieve uniform elongation.

 

Generally speaking, the main dislocation slip mode in alpha precipitates is prismatic<a>slip, as its critical resolved shear stress (CRSS) is the lowest among all slip systems. However, relying solely on this slip system cannot adapt to c-axis strain, nor can it meet the Taylor von Mises criterion. Therefore, it is necessary to activate pyramid shaped<c+a>slip, deformation twinning, or phase transition. Unfortunately, due to the different CRSS, these mechanisms are difficult to activate simultaneously, attributed to the inherent high stacking fault energy (SFE,>300 mJ/m2 pure alpha Ti) and strong grain size effects. Recent studies have shown that it is feasible to adjust the c/a ratio through Sn/Al alloying and transform the main slip mode from prismatic<a>to pyramidal<c+a>. At the same time, Al alloying significantly reduces the SFE of Ti, promotes deformation twinning, and even the transition from HCP to FCC.

 

This stress driven HCP to FCC phase transition was observed in Zr, Hf, and Ti alloys. Inspired by the above findings, in this work, we designed a sequentially activated multi plasticity mechanism (defined as SAPM) in the layered multiscale alpha precipitates of Ti-4.5Al-4.5Mo-7V-1.5Cr-1.5Zr (wt.%) alloy, thereby achieving a good strength ductility synergistic effect. By precisely controlling the particle size and morphology of alpha precipitates, a three peak titanium alloy with multi-scale and multi crystalline alpha precipitates was prepared. By utilizing the grain size dependent deformation mechanism, SAPM operates in multi-scale alpha crystals to gradually adapt to the applied load. This strategy results in our three peak titanium alloy having a high yield/ultimate tensile strength of 1550/1614 MPa and a ductility of approximately 8.7%, surpassing previously reported high-strength duplex titanium alloys.

 

 

Request a Quote

Email:bjcxtitanium@gmail.com       

               cxtitanium@outlook.com

Whatsapp:+8613571718779

Send Inquiry

whatsapp

Phone

VK

Inquiry